Maytag Services JDS9865BD* Specifications download pdf (Page 29)

To avoid risk of electrical shock, personal injury or

death; disconnect power and gas to range before

servicing, unless testing requires power and/or gas.

Disassembly Procedures

Bottom Access Panel Removal

(Select Models)

1. Grasp top of bottom access panel and gently pull

down and out.

2. Reverse procedure to reinstall bottom access panel.

Warming Drawer Removal (Select Models)

1. Slide warming drawer out until drawer stops.

2. Press tabs up or down (depending on side) on

warming drawer "stops" to release drawer from slide

track.

3. Slide warming drawer completely out of slide track.

4. Reverse procedure to reinstall warming drawer.

Warming Drawer Element Removal

(Select Models)

1. Remove warming drawer, see "Warming Drawer

Removal" procedure.

2. Remove screws securing element brackets to oven

chassis and element.

3. Remove element and slide toward front of unit.

4. Label and disconnect element wiring.

5. Reverse procedure to reinstall warming drawer

element.

Warming Drawer Hi-Limit Switch

Replacement (Select Models)

1. Remove unit from installation position, see “Removing

and Replacing Range” procedure.

2. Remove front side trim, see "Front Side Trim

Removal" procedure.

3. Remove warming drawer, see "Warming Drawer

Removal" procedure.

4. Remove screws securing side panel to oven chassis.

5. Remove screws securing sensor to warming drawer

cavity.

6. Label and disconnect sensor wire terminals.

7. Pull sensor in through warming drawer cavity to

remove (after labeling/disconnecting wire terminals).

8. Reverse procedure to reinstall warming drawer

sensor.

Oven Door Removal

WARNI NG

To avoid risk of personal injury or property damage, do

not lift oven door by the handle.

1. Open oven door slightly and grasp door on both sides.

2. Lift up and off the hinge receivers.

3. Reverse procedure to reinstall oven door.

Oven Door Hinge Removal

1. Remove power from unit.

2. Remove unit from installation position, see

“Removing and Replacing Range” procedure.

3. Remove oven door, see "Oven Door Removal"

procedure.

4. Remove front side trim, see "Front Side Trim

Removal" procedure.

5. Remove screws securing side panel to chassis.

6. Remove the top and bottom screws securing hinge

receiver to the front frame.

7. Remove hinge receiver from oven chassis.

8. Reverse procedure to reinstall oven door hinge.

Oven Door Disassembly

1. Remove oven door, see "Oven Door Removal"

procedure.

2. Place door on a protected surface.

3. Remove screws securing door glass to oven door

trim and frame (screws located along the top and

bottom edge of oven door).

NOTE: Proceed with the following steps if replacing door

handle.

4. Remove screws securing door handle to door glass.

5. Remove screws securing upper and lower shields.

6. Remove screws securing door baffle.

7. Remove oven door insulation.

8. Remove screws securing outer and inner door glass

(and glass frame).

9. Remove oven door liner, if replacing.

10.Reverse procedure to reassemble oven door.

Warming Drawer Disassembly

1. Remove warming door, see "Warming Drawer

Removal (Select Models)" procedure.

2. Place door on a protected surface.

3. Remove screws securing front panel to glass panel.

4. Remove screws securing front panel to warming

drawer.

5. Remove screws securing "sliding tracks" to warming

drawer.

6. Reverse procedure to reassemble oven door.

Warming Drawer Track Disassembly

1. Remove warming door, see "Warming Drawer

Removal (Select Models)" procedure.

2. Place door on a protected surface.

3. Remove screws securing front panel to glass panel.

4. Remove screws front panel to warming drawer.

5. Remove screws securing "sliding tracks" to warming

drawer.

6. Reverse procedure to reassemble oven door.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 72 73

Comments to this Manuals

No comments

Maytag Services JDS9865BD* Specifications Page 29

Comments to this Manuals